Contents IPsec VPNs for FortiOS 4.0 MR3 7 01-434-112804-20120111 http://docs.fortinet.com/ Configure the FortiGate unit .

Set Up IPSec Site to Site VPN Between Fortigate 60D (4) - SSL VPN Fortigate firewall supports two types of site-to-site IPSec vpn based on FortiOS Handbook 5.2, policy-based or route-based. There is little difference between the two types. However there is a difference in implementation. Go to VPN > IPsec > Tunnels and click Create New. Enter a name for the tunnel, which is Zscaler in this example, and select Custom VPN Tunnel as the template. Configure the primary tunnel as shown in the following figures. ipsec vpn using fortigate 60d / fortinet 5.2 and forticlient. good morning, we have used the conf decribed in the title for a while to allow external users to connect to an internal samba share. the setup followed the cookbook example. this worked very well until we changed the internet provider. the new provider uses ppoe, to support this we had to add a static route: To create the VPN, go to VPN > IPsec Wizard and create a new tunnel using a pre-existing template. Name the VPN. The tunnel name cannot include any spaces or exceed 13 characters. Set Template to Remote Access, and set Remote Device Type to FortiClient VPN for OS X, Windows, and Android. Set the Incoming Interface to wan1 and Authentication Method to Pre-shared Key. The network admin typically doesn't have direct access on the computers on either side of the VPN in order to initiate that traffic. I'll show you a method that can be used to initiate traffic from that network as well. Here are some basic steps to troubleshoot VPNs for FortiGate. In IKE/IPSec, there are two phases to establish the tunnel. The FortiGate sets an IPsec tunnel Maximum Transmission Unit (MTU) of 1436 for 3DES/SHA1 and an MTU of 1412 for AES128/SHA1, as seen with diag vpn tunnel list. This indicates that the FortiGate allocates 64 bytes of overhead for 3DES/SHA1 and 88 bytes for AES128/SHA1, which is the difference if you subtract this MTU from a typical ethernet MTU

This article seems to be the reference for IPsec Site-to-Site (route-based) VPN between FortiGate and Cisco Router. This helped me greatly to get a VPN tunnel up between my 2 devices (Fortigate 60C and Cisco 881W). I can ping from the Fortigate LAN to the Cisco LAN however I cannot ping from the Cisco to the Fortigate.

Jul 13, 2016 · Traffic to the Internet will also flow through the FortiGate, to apply security scanning. In this example, FortiClient 5.4 for Mac OS X is used and FortiOS 5.4.1. Comments are turned off. Contents IPsec VPNs for FortiOS 4.0 MR3 7 01-434-112804-20120111 http://docs.fortinet.com/ Configure the FortiGate unit . 1. Configuring the Cisco device using the IPsec VPN Wizard 2. Configuring the FortiGate tunnel phases 3. Configuring the FortiGate policies 4. Configuring the static route in the FortiGate 5. Results Configuring IPsec VPN with a FortiGate and a Cisco ASA. The following recipe describes how to configure a site-to-site IPsec VPN tunnel. This is for getting my home Fortinet 60D connected our colo, so not all my work devices need to have the VPN on. I'll update with how it goes. Tried a couple things, but deleting VPN configs the GUI is pain in the butt (maybe not possible, had to use CLI to kill some refs - the phase-interfaces) so wanted more direction since iterating was slow.

I have a firewall Fortigate 60D and I need to create a tunnel to a L2TP/IPSEC server, so the firewall has to act as a client. Is it possible? I configured the L2TP/IPSEC server on a Linux Debian machine using Libreswan and I can connect to it using an android phone but I am not able to do the same with the Fortigate firewall.

Next-generation firewalls filter network traffic to protect an organization from external threats. Maintaining features of stateful firewalls such as packet filtering, VPN support, network monitoring, and IP mapping features, NGFWs also possess deeper inspection capabilities that give them a superior ability to identify attacks, malware, and other threats. I have a firewall Fortigate 60D and I need to create a tunnel to a L2TP/IPSEC server, so the firewall has to act as a client. Is it possible? I configured the L2TP/IPSEC server on a Linux Debian machine using Libreswan and I can connect to it using an android phone but I am not able to do the same with the Fortigate firewall. Nov 22, 2016 · IPsec VPN between Cisco IOS and FortiGate - Part 2 - Tunnel Creation - Duration: 21:41. Route The Packet 7,920 views. 21:41. GRE Encryption with IPSec | VPN Tunnels Part 2 - Duration: 9:20.